ANIMA Washbasins

ANMX500 Washbasins
Wash basin for disabled for wall mounting, stainless steel, surface satin finished, material thickness 1.2 mm, seamless welded round bowl with diameter 350 mm, rectangular shape, 75 mm tap ledge, without overflow, seamless welded waste with 32 mm drain pipe, drainage centric, prewelded mouting brackets, for recessed trap mounting – trap not included, mounting conform to EN 31, disabled accessible mounting possible, includes stainless steel screws and dowels.

Width 500 mm, without taphole
Dimensions 500 x 105/160 x 500 mm (W x H x D)

ANMX501 Washbasins
Wash basin for disabled for wall mounting, stainless steel, surface satin finished, material thickness 1.2 mm, seamless welded round bowl with diameter 350 mm, rectangular shape, 75 mm tap ledge, without overflow, seamless welded waste with 32 mm drain pipe, drainage centric, prewelded mouting brackets, for recessed trap mounting – trap not included, disabled accessible mounting possible, includes stainless steel screws and dowels.

Width 500 mm, with taphole, centered
Dimensions 500 x 105/160 x 500 mm (W x H x D)

LP21 Washbasins
Single wash basin, floorstanding, wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded round bowl with diameter 380 mm, rectangular shape, 35 mm tap ledge, without overflow, 1 1/4″ plug waste, drainage centric, incl. premounted spout, floor standing trap cover with premounted self-closing valve for foot operation, water temperature adjustable with valve, front cover can be removed, includes screws and dowels.

Dimensions 450 x 880 x 451 mm (W x H x D)
Bowl Dimensions 380 x 150 mm (W x H)

WB240WM Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded round bowl with diameter 240 mm, semicircular shape, 45 mm tap ledge, without overflow, 1 1/2″ flat perforated waste, drainage centric, includes screws and dowels.

Dimensions 315 x 105 x 320 mm (W x H x D)

ANMX205 Washbasins
The Centinel washbasin is manufactured from 1.25 mm thick grade EN 1.4301 (304) stainless steel polished to a satin finish. The bowl is prepared with no tap hole and supplied with a 32 mm flush grated waste only (no overflow can be fitted). Complete with joggle strip and bottom access panel for fixing (using screws) and plumbing connections.

Dimensions 330 x 310 x 350 mm (W x H x D)
Bowl dimensions 277 x 140 mm (D x H)

ANMX450 Washbasins
Wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1.2 mm, seamless welded bowl with dimension 360 x 272 x 135 mm, made of one piece, for high risk vandalism areas due to seamless closed trap cover and semicircular shape, rounded edges, bowl with revolving channel, 40 mm tap ledge, without overflow, 1 1/2″ flat perforated waste, drainage centric, incl. trap DN 32, with pressed soap dish, inclusive mounting plate conform to EN 31, includes stainless steel screws and dowels.

Dimensions 450 x 280 x 400 mm (W x H x D)
Dimensions of bowl 360 x 150 x 270 mm (W x H x D)

BS204 Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 500 x 335 x 155 mm, oval shape, 90 mm tap ledge, prewelded mounting brackets, with soap dish, includes screws and dowels.

Without overflow, 1 1/4″ flat perforated waste
Dimensions 50 x 155 x 450 mm (W x H x D)

BS205 Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 500 x 335 x 155 mm, oval shape, 90 mm tap ledge, prewelded mounting brackets, with soap dish, includes screws and dowels.

With overflow, 1 1/4″ plug waste
Dimensions 550 x 155 x 450 mm (W x H x D)

WT400A Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 340 x 305 x 142 mm, rectangular shape, 80 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

Dimensions 400 x 200 x 412 mm (W x H x D)

WT400C Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 340 x 300 x 140 mm, rectangular shape, 120 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, mounting conform EN 31, includes screws and dowels.

Dimensions 400 x 150 x 452 mm (W x H x D)

WT500A Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 400 x 291 x 141 mm, rectangular shape, 70 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

Dimensions 500 x 200 x 402 mm (W x H x D)

WT500C Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 400 x 300 x 135 mm, rectangular shape, 105 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, mounting conform EN 31, includes screws and dowels.

Dimensions 500 x 150 x 446 mm (W x H x D)

WT600A Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 550 x 350 x 140 mm, rectangular shape, 75 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

Dimensions 600 x 200 x 440 mm (W x H x D)

WT600C Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 550 x 350 x 145 mm, rectangular shape, 90 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, distance between the centre lines of the fixing holes conform to EN 31, includes screws and dowels.

Dimensions 600 x 150 x 480 mm (W x H x D)

ANMX600 Washbasins
Wash basin for disabled for wall mounting, stainless steel, surface satin finished, material thickness 1.2 mm, seamless welded round bowl with diameter 350 mm, rectangular shape, 75 mm tap ledge, without overflow, seamless welded waste with 32 mm drain pipe, drainage centric, prewelded mouting brackets, for recessed trap mounting – trap not included, mounting conform to EN 31, disabled accessible mounting possible, includes stainless steel screws and dowels.

Width 600 mm, without taphole

ANMX601 Washbasins
Wash basin for disabled for wall mounting, stainless steel, surface satin finished, material thickness 1.2 mm, seamless welded round bowl with diameter 350 mm, rectangular shape, 75 mm tap ledge, without overflow, seamless welded waste with 32 mm drain pipe, drainage centric, prewelded mouting brackets, for recessed trap mounting – trap not included, mounting conform to EN 31, disabled accessible mounting possible, includes stainless steel screws and dowels.

Width 600 mm, with taphole, centered

C20136L Washbasins
Large rimmed edge bowls for insetting into worktops. Manufactured from 1.2 mm thick austenitic grade stainless steel with satin polish finish. An earthling lug is fitted to the underside of the bowl. Supplied with an 38 mm waste outlet and standpipe strainer overflow. Fixing studs, brackets and full fitting instructions are supplied. (L or R after the code number refers to the handing of the waste outlet i.e.. back left or back right hand corner.)

Overall inset sink bowl – rimmed edge
Left hand waste
Dimensions 635 x 300 x 485 mm (W x H x D)
Bowl Dimensions 600 x 300 x 450 mm (W x H x D)

C20136R Washbasins
Large rimmed edge bowls for insetting into worktops. Manufactured from 1.2 mm thick austenitic grade stainless steel with satin polish finish. An earthling lug is fitted to the underside of the bowl. Supplied with an 38 mm waste outlet and standpipe strainer overflow. Fixing studs, brackets and full fitting instructions are supplied. (L or R after the code number refers to the handing of the waste outlet i.e.. back left or back right hand corner.)

Overall inset sink bowl – rimmed edge
Right hand waste
Dimensions 635 x 300 x 485 mm (W x H x D)
Bowl Dimensions 600 x 300 x 450 mm (W x H x D)

ANMX216 Washbasins
Knee operated wash hand basin is manufactured from stainless steel – satin polish finish, material thickness 0.9 mm. Supplied complete with water spout positioned in rear right hand corner and 32 mm waste outlet. Note: The pre-mixing valve and the pipework linking the water spout to the knee operated front panel is all supplied with the washbasin. Wall mounted by fitting a top joggle strip under the upstand return and by screw fixing through the integral rear brackets. Screws and plugs are not supplied.

Dimensions 305 x 501 x 268 mm (W x H x D)
Bowl Dimensions 240 x 125 mm (W x D)

C20150N Washbasins
Small rimmed edged bowl for insetting into worktops. Manufactured from 0.9 mm thick grade 1.4301 (304) stainless steel with a satin polish finish. The bowl has a 20 mm rimmed edge and is prepared for a 38 mm waste and overflow. There are no tap holes therefore taps are to be mounted through the worktop or on the wall. Fixing clips are supplied with each bowl. Waste, plug, chain and overflow are available extras. NOTE: It may be necessary to notch the worktop when fitting an overflow.

20 mm rimmed edge
Centre waste
Dimensions 500 x 400 x 300 mm (W x H x D)
Cut-out size 510 x 410 mm

WT450 Washbasins
Single wash basin, stainless steel, material thickness 0.9 mm, surface satin finished, circular bowl with diameter 380 mm, rear upstand, single tap hole, 32 mm waste/overflow fitting, includes screws and dowels.

Tap hole right
Dimensions 450 x 175 x 450 mm (W x H x D)

WT360C Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 290 x 155 x 121 mm, rectangular shape, tap ledge, without overflow, 1 1/4″ waste, drainage centric, front panel with 45° corner edges, prewelded mounting brackets, mounting conform EN 31, includes screws and dowels.

Dimensions 360 x 150 x 250 mm (W x H x D)
Dimensions of bowl 290 x 121 x 155 mm (W x H x D)

BS204-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 500 x 335 x 155 mm, oval shape, 90 mm tap ledge, prewelded mounting brackets, with soap dish, includes screws and dowels.

Without overflow, 1 1/4″ flat perforated waste, with tap hole
Dimensions 550 x 155 x 450 mm (W x H x D)

BS205-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 500 x 335 x 155 mm, oval shape, 90 mm tap ledge, prewelded mounting brackets, with soap dish, includes screws and dowels.

Plug valve with 1 1/4″ with overflow and tap hole
Dimensions 550 x 155 x 450 mm (W x H x D)

WT500C-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 400 x 300 x 135 mm, rectangular shape, 105 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, mounting conform EN 31, includes screws and dowels.

With taphole
Dimensions 500 x 150 x 446 mm (W x H x D)

WT400A-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 340 x 300 x 140 mm, rectangular shape, 80 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

With taphole
Dimensions 400 x 200 x 412 mm (W x H x D)

WT400C-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 340 x 300 x 140 mm, rectangular shape, 120 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, mounting conform EN 31, includes screws and dowels.

With taphole
Dimensions 400 x 150 x 452 mm (W x H x D)

WT500A-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 500 x 400 x 200 mm, rectangular shape, 70 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

With taphole
Dimensions 500 x 200 x 402 mm (W x H x D)

WT600A-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 550 x 350 x 140 mm, rectangular shape, 75 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, prewelded mounting brackets, includes screws and dowels.

With taphole
Dimensions 600 x 200 x 440 mm (W x H x D)

WT600C-M Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 550 x 350 x 145 mm, rectangular shape, 90 mm tap ledge, with overflow, 1 1/4″ plug waste, drainage rewards centric, front panel with 45° corner edges, prewelded mounting brackets, Abstand zwischen den Achsen der Befestigungslöcher lt. EN 31, includes screws and dowels.

With taphole
Dimensions 600 x 200 x 440 mm (W x H x D)

ANMX206 Washbasins
Knee operated wash hand basin is manufactured from stainless steel-satin polish finish, material thickness 0.9 mm. Supplied complete with water spout positioned in rearright hand corner and 32 mm waste outlet. Note: The pre-mixing valve and the pipework linking the water spout to the knee operated front panel is all supplied with the washbasin. Wall mounted by fitting a top joggle strip under the upstand return and by screw fixing through the integral rear brackets. Screws and plugs are not supplied.

Dimensions 420 x 520 x 380 mm (W x H x D)
Bowl dimensions 410 x 265 mm (W x D)

CM1400 Washbasins
Wash basin, stainless steel, surface satin finished, material thickness 1.0 mm, with tap ledge 95 mm, without tap hole, waste G 1 1/2 B, includes screws and dowels.

2 basins
Dimensions 1400 x 170 x 514 mm (W x H x D) Bowl Dimensions 600 x 130 x 340 mm (W x H x D)

CM2100 Washbasins
Wash basin, stainless steel, surface satin finished, material thickness 1.0 mm, with tap ledge 95 mm, without tap hole, waste G 1 1/2 B, includes screws and dowels.

3 basins
Dimensions 2100 x 170 x 514 mm (W x H x D)
Bowl Dimensions 600 x 130 x 340 mm (W x H x D)

CM2800 Washbasins
Wash basin, stainless steel, surface satin finished, material thickness 1.0 mm, with tap ledge 95 mm, without tap hole, waste G 1 1/2 B, includes screws and dowels.

4 basins
Dimensions 2800 x 170 x 514 mm (W x H x D)
Bowl Dimensions 600 x 130 x 340 mm (W x H x D)

CM700 Washbasins
Wash basin, stainless steel, surface satin finished, material thickness 1.0 mm, with tap ledge 95 mm, without tap hole, waste G 1 1/2 B, includes screws and dowels.

1 basin
Dimensions 700 x 170 x 514 mm (W x H x D)
Bowl Dimensions 600 x 130 x 340 mm (W x H x D)

LP20 Washbasins
Single wash basin for wall mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded round sink with diameter 380 mm, 35 mm tap ledge, without overflow, 1 1/4″ plug waste, waste centric, incl. preassembled water spout, 200 mm high front panel with included self-closing valve for knee- or hip operations, watertemperature adjustable, includes screws and dowels.

Dimensions 450 x 204 x 451 mm (W x H x D)
Bowl Dimensions 380 x 150 mm (W x H)

WT310E Washbasins
Single wash basin for wall-corner mounting, stainless steel, surface satin finished, material thickness 1 mm, seamless welded bowl with diameter 290 x 155 x 100 mm, rectangular shape, with tap ledge, without overflow, 1 1/4″ flat perforated waste, drainage centric, front panel with 45° corner edges, includes screws and dowels.

Dimensions 310 x 121 x 310 mm (W x H x D) Bowl dimensions 290 x 121 x 155 mm (W x H x D)